Solar energy engineering

0 (Final Draft Jordanian Document (FDJS))

0 (Final Draft Jordanian Document (FDJS))

This standard specifies and desribes the fundamental construction requirement for photovoltaic (PV) modules in order to provide safe electrical and mechanical operation (Final Draft Jordanian Document (FDJS))

This part of the standard lists the tests a PV module is required to fulfill for safety qualification . IEC 61730-2 is applied for safety quakification only in conjunction with IEC 61730-1 (Final Draft Jordanian Document (FDJS))

This part of Jordanian standard, which is a Technical Specification, defines a procedure for measuring and analyzing the energy production of a specific photovoltaic system relative to expected electrical energy production for the same system from actual weather conditions as defined by the stakeholders of the test (Published Document (JS))

This part defines a procedure for measuring and analyzing the power production of a specific photovoltaic system with the goal of evaluating the quality of the PV system performance. The test is intended to be applied during a relatively short time period (a few relatively sunny days). (Published Document (JS))

This part of Jordanian standard outlines equipment, methods and terminology for performance monitoring and analysis of photovoltaic (PV) systems It addresses sensors, installation , and accuracy for monitoring equipment in addition to measured parameter data acquisition and quality checks calculated parameters, and performance metrics In addition, (Published Document (JS))

Photovoltaic (PV) modules are electrical devices intended for continuous outdoor exposure during their lifetime. Highly corrosive wet atmospheres, such as marine environments, could eventually degrade some of the PV module components (corrosion of metallic parts, deterioration of the properties of some non-metallic materials - such as protective coatings and plastics - by assimilation of salts, (Published Document (JS))

Photovoltaic (PV) modules are electrical devices intended for continuous outdoor exposure during their lifetime. Highly corrosive wet atmospheres, such as in the environment of stables of agricultural companies, could eventually degrade some of the PV module components (corrosion of metallic parts, deterioration of the properties of some non-metallic materials such as protective coatings (Published Document (JS))

his Jordanian Standard lays down IEC requirements for the design qualification and type approval of terrestrial photovoltaic modules suitable for long-term operation in general open-air climates, as defined in IEC 60721-2-1. This part of JS is intended to apply to all terrestrial flat plate module materials such as crystalline silicon module types as well as thin-film modules (Published Document (JS))

This part of JS 2248 lays down the requirements for the design qualification and type approval of terrestrial photovoltaic modules suitable for long-term operation in general open- air climates, as defined in IEC 60721-2-1. This document is intended to apply to all thin-film amorphous silicon (a-Si; a-Si/µc-Si) based terrestrial flat plate modules (Published Document (JS))

0 (Published Document (JS))

This part of JS 2248 lays down the requirements for the design qualification and type approval of terrestrial photovoltaic modules suitable for long-term operation in general open- air climates, as defined in IEC 60721-2-1. This document is intended to apply to all thin-film Cu(In,Ga)(S,Se)2 based terrestrial flat plate modules (Published Document (JS))

This part of JS 2248 lays down the requirements for the design qualification and type approval of terrestrial photovoltaic modules suitable for long-term operation in general open- air climates, as defined in IEC 60721-2-1. This document is intended to apply to all thin-film CdTe based terrestrial flat plate modules (Published Document (JS))

This part of JS 2248 lays down the requirements for the design qualification and type approval of terrestrial photovoltaic modules suitable for long-term operation in general open air climates, as defined in IEC 60721-2-1. This standard is intended to apply to all crystalline silicon terrestrial flat plate modules. (Published Document (JS))

This standard lays down IEC requirements for the drsign qulification and type approval of terrestrial photovoltaic (PV) modules suitable for lon-term operation in general open-air climents, as defined in IEC 60721-2-1. is intended to apply to all terrestrial flat plate module materials such as crystalline silicon module types as well as thin-film modules. (Published Document (JS))

This Jordanian standard sets out design requirements for photovoltaic (PV) arrays including DC array wiring, electrical protection devices, switching and earthing provisions. The scope includes all parts of the PV array up to but not including energy storage devices, power conversion equipment or loads (Published Document (JS))

This part of Jordanian standard defines the information and documentation required to be handed over to a customer following the installation of a grid connected PV system. It also describes the commissioning tests, inspection criteria and documentation expected to verify the safe installation and correct operation of the system. It can also be used for periodic retesting. (Published Document (JS))

This part of the standard applies to the following photovoltaic devices for terrestrial applications: solar cells with or without a protective cover; sub- assemblies of solar cells; modules; systems. The principles contained in this standard cover testing in both natural and simulated sunlight. This standard is not applicable to solar cells designed for operation in concentrated sunlight (Published Document (JS))

This part of JS 2118 gives requirements for the classification, selection, packaging, marking, calibration and care of photovoltaic reference devices. This standard covers photovoltaic reference devices used to determine the electrical performance of photovoltaic cells, modules and arrays under natural and simulated sunlight. It does not cover photovoltaic reference devices for use under (Published Document (JS))

This Standard applies to utility-interconnected photovoltaic (PV) power systems operating in parallel with the utility and utilizing static (solid-state) non-islanding inverters for the conversion of DC to AC (Published Document (JS))

This standard establishes requirements for the design qualification of balance of system (BOS) components used in terrestrial photovoltaic (PV) systems. This standard is suitable for operation in indoor, conditioned or unconditioned; or outdoor in general open-air climates as defined in IEC 60721-2-1, protected or unprotected. (Published Document (JS))

This standard defines requirements for the design qualification and type approval of terrestrial, thin-film photovoltaic modules suitable for long-term operation in general open-air climates as defined in IEC 60721-2-1. This standard is intended to apply to all terrestrial flat plate module materials not covered by IEC 61215. (Withdrawn Document)

This Jordanian Standard lays down IEC requirements for the design qualification and type approval of terrestrial photovoltaic modules suitable for long-term operation in general open air climates. It applies only to crystalline silicon modules types. This Jordanian standard does not apply to modules used with concentrated sunlight. (Withdrawn Document)

The purpose of standard is to provide a test procedure to evaluate the performance of islanding prevention measures used with utility-interconnected PV systems (Published Document (JS))

This Jordanian Standard specifies requirements on durability, reliability and safety for Factory Made thermal solar heating systems. The standard also includes provisions for evaluation of conformity to these requirements. The requirements in this standard apply to Factory Made solar systems as products. The installation of these systems itself is not considered, (Published Document (JS))

This Jordanian Standard specifies test methods for validating the requirements for Factory made thermal solar heating systems as specified in JS 1992-1 The standard also includes two test methods for thermal performance characterization by means of whole system testing. (Published Document (JS))

This Standard defines characterization of domestic water heating systems performance by means of component tests and computer simulation (Published Document (JS))

This Standard defines characterization of domestic water heating systems performance by means of whole-system tests and computer simulation (Published Document (JS))

This standard defines procedures to be followed for temperature and irradiance corrections to the measured I-V (current-voltage) characteristics of photovoltaic devices. (Published Document (JS))

This standard describes guidelines for measuring the efficiency of power conditioners used in stand-alone and utility-interactive photovoltaic systems. (Published Document (JS))

This Standard defines a test which determines the resistance of the module when exposed to ultra-violet (UV) radiation. This test is useful for evaluating the UV resistance of materials such as polymers and protective coatings. (Published Document (JS))

This part of JS 2118 describes procedures for the measurement of current-voltage characteristics of photovoltaic devices in natural or simulated sunlight. These procedures are applicable to a single photovoltaic solar cell, a sub-assembly of photovoltaic solar cells, or a PV module. (Published Document (JS))

This Standard specifies test methods for assessing the durability, reliability and safety for fluid heating collectors. This Standard also includes test methods for the thermal performance characterization of fluid heating collectors, namely steady-state and quasi-dynamic thermal performance of glazed and unglazed liquid heating solar collectors and steady-state thermal performance (Published Document (JS))

This part of EN 61730 describes the testing requirements for photovoltaic (PV) modules in order to provide safe electrical and mechanical operation during their expected lifetime. (Published Document (JS))

This part of EN 61730 describes the fundamental construction requirements for photovoltaic (PV) modules in order to provide safe electrical and mechanical operation during their expected lifetime. Specific topics are provided to assess the prevention of electrical shock. (Published Document (JS))

0 (Committee Draft (CD))

This standard specifies thelabelling of solar water heater (Withdrawn Document)

This part of the standard establishes test procedure for characterizing the performance of solar domestic water heating systems operated without auxiliary boosting, and for predicting annual performance in any given climatic and operating conditions, but only for evening draw-off. The test procedures are applicable only to solar water heating systems designed to heat potable water to be supplied (Published Document (JS))

this part establishes methods for determining the thermal performance of glazed liquid heating solar collectors and it provides test methods and calculation procedures for determining the steady state and quasi- steady state thermal performance of solar collectors itcontain methods for conducting tests outdoors under natural solar irradiance and for conducting tests indoors under simulated solar i (Withdrawn Document)

This part of the standard establish a uniform indoor test method for rating solar domestic water heating systems for thermal performance, under benchmark conditions. The test procedures are applicable only to solar water heating systems designed to heat potable water to be supplied for domestic water usage of 0.6m3 of solar storage capacity or less. (Published Document (JS))

Specifies the design, construction, installation, workmanshipand commissioning of components and system for flat plate solarcollector (Published Document (JS))

This partspecifies test methods for determining the ability of solar collectorto resist the influences of degrading agent, and it definesprocedures for testing collectors under well-defined and repeatableconditions. (Withdrawn Document)

This part of the standard establishes test procedures for characterizing the performance of solar domestic water heating systems with in-tank auxiliary boosting, and for predicting annual performance in any given climatic conditions. The test procedures are applicable only to solar water heating systems designed to heat potable water to be supplied for domestic water usage. (Published Document (JS))

Includestesting methods to determine flat plate solar collector performanceand thermal efficiency (Withdrawn Document)

Includes terms, definitions, units and symbols concerning flat platesolor collector (Withdrawn Document)

Concerns constructionrequirements for flat plate solar collector whose work depends on sunrays concentration (Withdrawn Document)

Specifies values and data that must appear on the dataplate of solar water heaters (Withdrawn Document)