Electrical engineering in general

This Jordanian Standard sets the emission limits from the whole railway system including urban vehicles for use in city streets. It describes the measurement method to verify the emissions, and gives the cartography values of the fields most frequently encountered. (Published Document (JS))

This Part 1 of the Jordanian standards series EN 50121 outlines the structure and the content of the whole set. This part alone is not sufficient to give presumption of conformity to the essential requirements of the EMC-Directive and must be used in conjunction with other parts of this standard. (Published Document (JS))

This Standard specifies requirements and procedures to integrate environmental aspects into design and development processes of electrical and electronic products, including combination of products, and the materials and components of which they are composed (hereafter referred to as products). (Published Document (JS))

This standard applicable to mains-powred or battery-powred information technology equipment including electrical business equipment and associated equipment with a rated voltage not exeeding 600 V. (Published Document (JS))

This part of JS 60950 specifies requirements for information technology equipment (ITE) with self contained data storage systems that contain hazardous moving parts. These data storage systems are typically large enough to permit a person to enter completely, however, the systems (Published Document (JS))

This part of IEC 60950 applies to information technology equipment intended to be installed in an OUTDOOR LOCATION. The requirements for OUTDOOR EQUIPMENT also apply, where relevant, to empty OUTDOOR ENCLOSURES supplied for housing information technology equipment to be installed in an OUTDOOR LOCATION. (Draft Jordanian Document (DJS))

For a given current path through the human body, the danger to persons depends mainly on the magnitude and duration of the current flow. However, the time/current zones specified in this publication are, in many cases, not directly applicable in practice for designing measures of protection against electrical shock. (Published Document (JS))

This part of IEC 60950 applies to information technology equipment intended to be installed in an OUTDOOR LOCATION. (Published Document (JS))

ٍٍٍٍٍSpecifies a small-scale laboratory screening procedure for comparing the relative burning behaviour of specimens made from plastics and other non-metallic materials, as well as their resistance to burn-through when exposed to a aflame ignition source. of 500 W nominal power. (Published Document (JS))

This part of standrad applicable to electrotechnical equipment including parts made from polymeric materials. this test is intended to simulate the effects caused by the relieving of moulding stresses by conditioning the product or part at a temperature higher than the maximum normal operating temperature and observing the nature of the resulting changes (Published Document (JS))

This part of standard specifies a needle-flame test to simulate the effect of a small flame which may result from fault conditions, in order to assess by a simulation technique the fire hazard. It is applicable to electrotechnical equipment, its sub-assemblies and components and to solid electrical insulating materials or other combustible materials. (Published Document (JS))

Specializes in this specification in ways test the seriousness of the fire on the basis of glowing hot wire and in a manner examine the flammability of incandescent wire of the end products (Published Document (JS))

This part of standard specifies the glow-wire apparatus and common test procedure to simulate the effect of thermal stresses which may be produced by heat sources such as glowing elements or overloaded resistors, for short periods, in order to assess the fire hazard by a simulation technique. (Published Document (JS))

Shall be standard guidelines for assessing the general seriousness of the fire products Electrotechnical Commission (Published Document (JS))

This part of standard specifies the details of the glow-wire test to be applied to test specimens of solid electrical insulating materials or other solid materials for ignitability testing to determine the glow-wire ignition temperature (GWIT). (Published Document (JS))

This part ofstandard specifies the ball pressure test as a method for testing parts of nonmetallic materials for resistance to heat. It is applicable to electrotechnical equipment, its subassemblies and components, and to solid electrical insulating materials except ceramics. (Published Document (JS))

This part of standard specifies the details of the glow-wire test to be applied to test specimens of solid electrical insulating materials or other solid materials for flammability testing to determine the glow-wire flammability index (GWFI). (Published Document (JS))

This part of standard specifies a small-scale laboratory screening procedure for comparing the relative burning behaviour of vertically or horizontally oriented specimens made from plastic and other non-metallic materials, exposed to a small-flame ignition source of 50 W nominal power. (Published Document (JS))

This standard applies to the protection of persons and animals against electric sock it is intended to give fundamental principles and requirements which are common to electrical installations systems and equipment or necessary for their co-ordination. (Published Document (JS))

This part of JS 61010 specifies general safety requirements for electrical equipment intended for professional, industrial process, and educational use, any of which may incorporate computing devices, as defined in a) to d) below, when used under the environmental conditions of 1.4. (Published Document (JS))

This standard provides general rules for the use of certain colours or alphanumerics to identify conductors with the aim of avoiding ambiguity and ensuring safe operation. these conductor colours or alphanumerics are intended to be applied in cables or cores, busbars, electrical equipment and installations (Published Document (JS))

This standard applies to the application of electrical, electronic and programmable electronic equipment and systems to machines not portable by hand while working, including a group of machines working together in a co-ordinated manner. (Published Document (JS))

This standard provides details of the test apparatus to be used for measuring smoke emission when electric or optical fiber cables are burnt under define conditions, (Published Document (JS))

This Standard for electromagnetic immunity requirements applies to lighting equipment which is within the scope of IEC technical committee 34, such as lamps, auxiliaries and luminaires, intended either for connecting to a low voltage electricity supply or for battery operation. (Published Document (JS))

This part of IEC 60332 specifies the test apparatus for testing the resistance to vertical flame propagation for a single small vertical electrical insulated conductor or cable, or optical fibre cable, under fire conditions. (Published Document (JS))

This part of IEC 60332 specifies the test apparatus for testing the resistance to vertical flame propagation for single vertical electrical insulated conductor or cable or optical fibre cable under fire conditions. (Published Document (JS))

This standard applies to the identification and marking of terminals of electrical equipment such as resistors, fuses, relays, conductors, transformers, rotating machines and wherever applicable, to combination of such equipment (Published Document (JS))

concerns degrees of protection provided by enclosures (IP code) (Withdrawn Document)

gives the standard related currentvalues for electric appliances (Published Document (JS))

Concerns voltage system for transmission distribution and utilization (Published Document (JS))

Concerns the standard voltage system fortransmission, distribution and utilization (Withdrawn Document)

Concernselectrotechnical symbols for architectural and topographicalinstallation plans and diagrams in order to be united and understoodby engineers and technicians working in the electrical sector (Withdrawn Document)

Gives the standard rated currunt valueswithin the range 1-1000 ampere (Withdrawn Document)

Includes testing and protection methods of enclosures forlow-voltage switchgear and controlgear (Withdrawn Document)