Concrete and concrete products

Search Results
JS 2232:2019 Environmental friendly construction products - Concrete - Ready mixed concrete, pre-cast concrete, concrete products and dry bagged mortars

This Jordanian Standard specifies the requirements for Environmental friendly Concrete products, Ready Mixed Concrete, Pre-cast Concrete, Concrete Products and Dry Bagged Mortars (Published Document (JS))

JS 2238-4:2019 Cement – Methods of testing cement Part 4: Quantitative determination of constituents

This part specifies the test method of determining the contents of most of the constituents of the cements, that fall within the scope of JS 30-1. (Published Document (JS))

JS 479:2018 Concrete kerb units - Requirements and test methods

This Jordanian Standard specifies materials, properties, requirements and test methods for unreinforced, cement bound precast concrete kerb units, channels and complementary fittings, that are for use in trafficked paved areas and roof coverings. -The units are used to fulfil one or more of the following: -Separation, physical or visual delineation, the provision of drainage (Published Document (JS))

JS 979:2018 Lightweight aggregates for thermal insulating concrete

This specification covers lightweight aggregates intended for use in concrete not exposed to the weather, in which the prime consideration is the thermal insulating property of the resulting concrete (Published Document (JS))

JS 2133-6:2017 Admixtures forconcrete, mortar and grout Part 6: Sampling, conformity controland evaluation of conformity

This Jordanian Standard specifies procedures for sampling, conformity control and evaluation of conformity, for admixtures according to the series JS 2133 , this JS explain sampling for Liquid admixture from containers, from a tank load, Conformity Criteria, Initial type testing, Factory production control. (Published Document (JS))

JS 2065:2017 Standard specifications for concrete aggregates

This specification defines the requirements for grading and quality of fine and coarse aggregate (other than lightweight or heavyweight aggregate) for use in concrete. (Published Document (JS))

JS 2065:2016 Standard specification for concrete aggregates

This Jordanian Standard defines the requirements for grading and quality of fine and coarse aggregate (other than lightweight or heavyweight aggregate) for use in concrete. (Withdrawn Document)

JS 2133-2:2016 Admixtures for concrete, mortar and grout Part 2- Concrete admixtures – Definitions, requirements, conformity, marking and labeling

This Jordanian Standard specifies definitions and requirements for admixtures for use in concrete. It covers admixtures for plain, reinforced and prestressed concrete which are used in site mixed, ready mixed concrete and precast concrete. The performance requirements in this standard apply to admixtures used in concrete of normal consistence. They may not be applicable to admixtures intended (Published Document (JS))

JS 949:2016 Lightweight aggregates for structural concrete

this specification covers lightweight aggregates intended for use in structural concrete in which prime considerations are reducing the density while maintaining the compressive strength of the concrete. Procedures covered in this specification are not intended for job control of concrete. (Published Document (JS))

JS 948:2016 Lightweight aggregates for concrete masonry units

This specification covers lightweight aggregates intended for use in concrete masonry units when a prime consideration is to reduce the density of the units. (Published Document (JS))

JS 2128:2015 Environmental friendly construction products - Blocks, tiles, and concrete boards

This Jordanian standard shall apply to blocks (For the block type, hollow concrete blocks, bricks, bordering blocks for sidewalks and driveways, interlocking blocks for sidewalks and driveways, and concrete waterfront blocks shall be included), tiles (For tile types, JS 374 (ceramic tile) and JS 45-1, JS 45-2 (precast terrazzo) shall be included), and board materials (For board materials, (Withdrawn Document)

JS 2027:2013 Standard specification for solid concrete interlocking paving units

0 (Published Document (JS))

JS 1979:2011 Precast concrete products – Classification of glassfibre reinforced concrete performance

This Jordanian Standard deals with the classification of glassfibre reinforced concrete. This classification conforms to the needs of the design process of glassfibre reinforced concrete components. (Published Document (JS))

JS 1906-1:2010 Concrete masonry units Part 1: Solid and hollow non load bearing concrete masonry units

This standard is concerned with the requirement that should be available in solid and hollow non load bearing concrete masonry units (Published Document (JS))

JS 979:2010 ٍٍStandard Specification for Lightweight aggregates for thermal insulation of concrete

This standard covers lightweight aggregates intended for use in concrete which is not exposed to the weather, in which the prime consideration is the thermal insulating property of the concrete made of this aggregates (Withdrawn Document)

JS 45-2:2010 Terrazzo tiles Part 2: Terrazzo tiles for external use

This standard specifies materials properties and methods of testing for unreinforced cement-bound terrazzo tiles which are factory made and sold ready to be placed the tiles are intended for external use(including roffing applications) in pedestrain areas walkways terraces and for external and internal use in commerical centers and swimming-pools schools hospitals and public and public building (Published Document (JS))

JS 1906-2:2010 Concrete masonry units Part 2: Solid and hollow non load bearing concrete masonry units

This standard is concerned with the requirement that should be available in solid and hohhow non load bearing concrete units (Published Document (JS))

JS 45-1:2009 Terrazzo tiles Part 1: Terrazzo tiles for internal use

This Jordanian Standard specifies material properties and methods of testing for unreinforced cement-bound terrazzo tiles which are factory made and sold ready to be placed (Published Document (JS))

JS 1865-4:2009 Masonry units Part 4 : Autoclaved aerated concrete masonry blocks

This Standard specifies the characteristics and performance requirements of autoclaved aerated concrete (AAC) masonry units for which the main intended uses are different types of load bearing and non-load bearing applications in all forms of walling including single leaf, cavity, partitions, retaining, basement and general use below ground level, including walling for fire protection. (Published Document (JS))

JS 10030-1:2007 Fly ash for concrete Part 1: Definition, specifications and conformity criteria

This dicument specfies requirements for the chemical and physical properties as well as quality control procedures for siliceous fly ash, as defined in 3.2 for use as type II addition for production of concrete, including in particular cast-in-situ or prefabricated structural concrete conforming to EN 206-1. fly ash according to this document may also be used in mortars and grouts. (Published Document (JS))

JS 45-1:2007 Terrazzo tiles Part 1: Terrazzo tiles for internal use

This standard specifies materials, properties and methods of testing for unreinforced cement-bound terrazzo tiles which are factory made and sold ready to be placed. (Withdrawn Document)

JS 45-2:2007 Terrazzo tiles- Part 2: Terrazzo tiles for external use

This standard specifies materials, properties ans methods of testing for unreinforced cement-bound terrazzo tiles which are factory made and sold ready to be placed. The tiles are intended for external use (including roofing applications) in pedestrian areas, e.g. walkways, terraces, commercial centres and swimming-pools, (Withdrawn Document)

JS 1673-1:2005 Fly ash-Method of testing fly ash Part1 :Determination of free calcium oxide content

This standard describes the reference procedurefor the determination of free calcium oxide content in fly ash. if other methods are used it shall be shown that they give results equivalent those obtained by the reference method (Published Document (JS))

JS 498:2005 Concrete -Specifications, performance, production and conformity

This standard applies to concrete for structures cast in site, precast structures, and structural precast products for buildings and civil engineering.This standard applies to concrete compacted to retain no appricable amount of entrapped air other than entrained air.This standard applies to normal-weight, heavy- weight , and light- weight concrete (Published Document (JS))

JS 1651-7:2004 Concrete - Testing fresh concrete Part 7: Air content - Pressure methods

this standard specifies the method for determing the density of compacted fresh concrete both in the labortory and in the field (Published Document (JS))

JS 1651-8:2004 Concrete -Testing fresh concrete part 8: Air content -Volumetric method

this method covers determination of the air content of fresh concrete (Published Document (JS))

JS 1652-1:2004 Concrete – Testing hardened concrete Part 1: Shape, dimensions and other requirements for specimens and moulds

this standard specifies the dimentions and tolerances of cast concrete test specimens in the form of cubes,cylindres,and prisms,and the moulds required to produce them. (Published Document (JS))

JS 1653-2:2004 Concrete - Testing concrete in structures Part 2: Non-destructive testing-determination of rebound number

this standard specifies method fordetermining the rebound number of anarea of hardened concreteusing aspring-driven steel hammer (Published Document (JS))

JS 1651-3:2004 Concrete – Testing fresh concrete Part 3- Vebe test

this standard specifies a method for determining the consisteency of concret by means of the veb time (Published Document (JS))

JS 1652-3:2004 Concrete – Testing hardened concrete Part 3- Compressive strength of test specimens

this standard detrmines tests of hard concrete (Published Document (JS))

JS 1651-5:2004 Concrete – Testing fresh concrete Part 5- Flow table test

this standard specifisa method for determining the flow of fresh concreat it is not applicable to foamed concrete or no-fines concrete (Published Document (JS))

JS 1652-7:2004 Concrete - Testing hardened concrete Part 7: Density of hardened concrete

this standard specifies amethod for determining the densiry of hardened concrete (Published Document (JS))

JS 1652-5:2004 Concrete - Testing hardened Concrete Part 5: Flexural strength of test specimens

this standard specifies method for the determination of the flexural strength of specimens of hardened concrete (Published Document (JS))

JS 1652-2:2004 Concrete – Testing hardened concrete Part 2: Making and curing specimens for strength tests

This stanadard specfies the standard test methed for concrete with water alkali is relesed ,take precaution to avoid dry cement entering the eyes moulds compaction of the concrete levelling the surface (Published Document (JS))

JS 1651-1:2004 Concrete - Testing fresh concrete part 1: Sampling

This standerd specifies two procedures for sampling fresh concrete, by composite sampling and by spot sampling (Published Document (JS))

JS 1651-2:2004 Concrete -Testing fresh concrete part 2: Slump test

This standard specifies a method for determining the consistency of fresh concrete by the slump test (Published Document (JS))

JS 1652-8:2004 Concrete – Testing hardened concrete Part 8: Depth of penetration of water under pressure

this standrad specifies amethod for determining the depth of penetration water under pressure in hardened concrete which has been water cured (Published Document (JS))

JS 1653-1:2004 Concrete - Testing concrete in structures part 1: cored specimens - Taking, examining and Testing in comperrion

this standard specifies amethod for taking cores from hardened concrete their examination prepartion for testing and determination of compressive stregth (Published Document (JS))

JS 1651-6:2004 Concrete - Testing fresh concrete part 6: density

this standard amethod for determining the density of compacrete both in the laboratory and in the field (Published Document (JS))

JS 1651-4:2004 Concrete – Testing fresh concrete Part 4- Degree of compactability

this standrad specifies amethod for determining the consistency of fresh concrete by determining the degree of compactability (Published Document (JS))

JS 1652-6:2004 Concrete - Testing hardened concrete part 6: Testing splitting strength of test specimens

this standard specifies method for the determination of the tensile splitting strength of cylindrical test specimens of hardened concrtet (Published Document (JS))

JS 1652-4:2004 Concrete - Testing hardened concrete Part 4: compressive strength-specification for testing machines

this standard specifies the reguirements for the performance of compression testing machines for the measurement of the compressive strength of concrete (Published Document (JS))

JS 979:1994 Concrete - Lightweight aggregates forthermal insulation of concrete

Concerns lightweight aggregates used for thermallyinsulated concrete which it's unexposed to atmosphere (Withdrawn Document)

JS 479:1994 Construction materials - Precast concrete kerbs

Specifies the requirements for precast cocrete kerbs which areused as rims for streets and walks (Withdrawn Document)

JS 949:1993 Concrete - Light weight aggregates forstructural concrete

Concerns light weight aggregates used in structural concrete (Withdrawn Document)

JS 948:1993 Concrete - Light weight aggregates for concrete masonry units

Concerns light weight aggregates used in concrete masonryunits (Withdrawn Document)

JS 944:1993 Construction materials - Blocks -Hollow blocks for slabs - Part 1: Concrete blocks

Concerns concrete blocks used inconstruction (Published Document (JS))

JS 276:1992 Construction materials - Cellularconcrete blocks of (70 mm) thickness

Concerns cellular concrete blocks of (70) mmthickness (Withdrawn Document)

JS 277:1992 Construction materials - Solidconcrete blocks of (70 mm) thickness

Concerns solid concrete blocks of (70mm) thickness (Withdrawn Document)

JS 84:1992 Construction materials - Cellular concrete blocks of thickness (100,120,150,200) mm

Concerns the requirementsfor cellular concrete blocks of thickness (100,120,150,200) mm usedfor walls construction (Withdrawn Document)

JS 123:1992 Construction materials - Solid concrete blocks of thickness (100,120,150,200) mm

Concerns solid concreteblocks of thickness (100,120,150,200) mm used in walls construction (Withdrawn Document)

JS 690:1990 Concrete - Concrete admixtures - Partthree

Specifiesthe requirements (Withdrawn Document)

JS 689:1990 Concrete - Concrete admixtures - Parttwo

Specifies therequirements and testing methods for air-containing concreteadmixtures (Withdrawn Document)

JS 673:1989 Concrete - Concrete admixtures -Methods of sampling concrete admixtures

Concerns sampling methods of concreteadmixtures present in powder or liquid form (Withdrawn Document)

JS 674:1989 Concrete - Concrete admixtures - Partone

Specifies therequirements (Withdrawn Document)

JS 575:1988 Concrete - Methods of sampling fresh concrete

Concerns Sampling methods for fresh concrete in order to be tested (Withdrawn Document)

JS 96:1987 Concrete - Aggregates for concrete

Includes theproperties of aggregates used for concrete (Withdrawn Document)

JS 498:1987 Concrete - Ready mixed concrete

Concerns materialsselection, manufacturing (Withdrawn Document)