Fluorescent lamps. Discharge lamps

This standard specifies the performance requirements for high-pressure mercury vapour lamps for general lighting purposes, with or without a red correcting fluorescent coating. For some of the requirements given in this standard, reference is made to “the relevant lamp data sheet”. For some lamps these data sheets are contained in this standard. (Published Document (JS))

This standard specifies the test conditions and method of measurement of luminous flux, lamp wattage and lamp life as given on a label on the lamp packaging, together with a procedure for verification of the declared values. Only those parameters that are specific to the above mentioned Directive are included in this standard. All other parameters are included in the relevant lamp performance (Published Document (JS))

This International Standard specifies the safety requirements for discharge lamps (excluding fluorescent lamps) for general lighting purposes. This International Standard is applicable to low-pressure sodium vapour lamps and to high intensity discharge (HID) lamps, i.e. high-pressure mercury vapour lamps (including blended lamps), high-pressure sodium vapour lamps and metal halide lamps. (Published Document (JS))

This standard covers a range of tubular fluorescent lamps for general lighting service which are operated on a.c. mains. Lamps of the following types are included:1. Lamps, with pre-heated cathodes, for operation on a.c. mains with the use of a starter.2. Lamps, with pre-heated cathodes, for operation on a.c. mains without the use of a starter. (Published Document (JS))

This Standard specifies the safety and performance requirements of a range of single-capped fluorescent lamps which are operated on a.c. supplies. (Published Document (JS))

This standard specifies interchangeable glow-starters used with pre-heat type fluorescent lamps, hereafter called "starters". (Published Document (JS))

This part of standard applies to the evaluation of thermal protectors for ballasts for tubular fluorescent lamps. (Published Document (JS))

This standard specifies lamps, or information relevant to lamps, not given elsewhere in existing IEC lamp standards (Published Document (JS))

Specifies the methods of test to be used to determine the characteristics of both single-ended and double-ended metal halide lamps operated on 50 or 60 Hz. (Published Document (JS))

Safety and interchangeability together with test methods and conditions of tubular fluorescent and other gas-discharge lamps with integral means of controlling starting and stable operation intended for domestic and similar general lighting purposes. (Published Document (JS))

This Standard states the requirements for both self-healing and non-self-healing continuously rated a.c. capacitors of up to and including 2,5 kVAr, and not less than 0,1 ?F, having a rated voltage not exceeding 1 000 V, which are intended for use in discharge lamp circuits operating at 50 Hz or 60 Hz and at altitudes up to 3 000 m. (Published Document (JS))

Specifies the lamp dimensions, electrical characteristics necessary to ensure interchangeability and safety together with test conditions and procedures (Published Document (JS))

This standard specifies the safety requirements for single-capped fluorescent lamps for general lighting purposes of all groups having 2G7, 2GX7, GR8, 2G10, G10q, GR10q, GX10q, GY10q, 2G11, G23, G24 and GX32 caps. (Published Document (JS))

This standard specifies the safety requirements for double-capped fluorescent lamps for general lighting purposes of all groups having Fa6, Fa8, G5, G13, 2G13, R17d and W4.3*8.5d caps. (Published Document (JS))

This standard specifies performance requirements for ballasts, excluding resistance types, for use on a.c. supplies up to 1 000 V at 50 Hz or 60 Hz, associated with tubular fluorescent lamps with pre-heated cathodes operated with or without a starter or starting device and having rated wattages, transformers and capacitors. (Published Document (JS))

Specifies the performance requirements for single-capped fluorescent lamps for general lighting service.The requirements of this standard relate only to type testing. Conditions of compliance, including methods of statistical assessment, are under consideration. This consolidated version consists of the second edition (1996) (Withdrawn Document)

this standard cover preformance requirement for electronic ballasts fore use on a.c supplies up to 1000 v at 50 h z with opearating freqencies (Published Document (JS))

This standard specifies characteristics, technical requirements and the test methods to be used for type, batch or whole production testingof doble capped flourescent lamps. (Withdrawn Document)

Specifies the safety requirements for discharge lamps (excluding flourescent lamps) for general lighting purposes (Withdrawn Document)

Specifies performance requirements for ballasts associated with tubular fluorescent lamps with pre-heated cathodes (Withdrawn Document)

Concerns performance and test requirements for replaceableglow-starters used for preheat fluorescent lamps (Withdrawn Document)

Concerns performance and test requirements for replaceableglow-starters used for preheat fluorescent lamps (Withdrawn Document)

Concerns general & safety requirements for replaceable glow-starters used for preheat fluorescent lamps (Withdrawn Document)

Concerns testing and adaption of tubular fluorescent lamps andits accessories for general lighting purposes (Withdrawn Document)